Professional Epoxy Flooring Built for BC's Climate
We install professional floor coating systems for homeowners and businesses across Greater Vancouver and BC. Every installation starts with diamond grinding and moisture testing: the two steps most contractors skip, and the main reason most epoxy floors fail within a few years in this climate.
(604) 742-9479
A Floor Coating Company That Does the Prep Right
Epoxy Floor Vancouver installs professional floor coating systems for residential and commercial clients across Greater Vancouver, the Fraser Valley, and Vancouver Island.
We specialize in epoxy garage floors, metallic epoxy feature floors, polyaspartic coatings, polished concrete, and commercial floor systems, installed using the same multi-coat methods used in industrial and pharmaceutical-grade environments.
Greater Vancouver's coastal climate creates specific challenges that most flooring companies don't address properly. The combination of high annual rainfall, one of the highest water tables in Canada, and a large proportion of older concrete slabs means that moisture vapour emission is a factor on a significant percentage of the floors we test. Applying standard epoxy to a slab with high MVER without a moisture-tolerant primer is the single most common reason epoxy floors fail in this market.
Across BC, the same lesson holds on floor after floor: the prep decides whether a floor lasts. That means diamond grinding instead of acid etching, a moisture test on every slab, cracks repaired before coating, and each coat built to the right thickness. We apply the same process to every job we take, residential or commercial.
We test every slab before we specify a system. Where moisture is a factor (and in Vancouver, it often is), we apply a dedicated moisture vapour barrier primer before any decorative coat. Flake floors come with a written warranty.
-
Garage Epoxy Floors Flake broadcast and solid colour systems, from $6/sq ft
-
Metallic Epoxy Three-dimensional marbled feature floors, from $12/sq ft
-
Polyaspartic Coatings UV-stable, fast-cure floor systems, from $6/sq ft
-
Polished Concrete Mechanically polished slab finish, from $6/sq ft
-
Commercial & Industrial Warehouse, restaurant, strata, and retail floor systems, quoted on-site
What We Do on Every Single Job
These aren't optional steps we upsell. They're the baseline for every installation we do, regardless of the system, the square footage, or the budget.
Moisture Testing
Calcium chloride MVER test and relative humidity probe measurement on every slab before any system is specified. This step determines whether a standard primer or a dedicated moisture vapour barrier coat is required. Skipping it is the most common reason epoxy fails in Vancouver.
Diamond Grinding
Every slab is ground to CSP 2 to 3 profile using industrial diamond grinders. No acid etching, no shot blast substitution for residential work. Mechanical profile is what allows epoxy to bond at the molecular level instead of just sitting on the surface.
Moisture-Tolerant Primer
Applied on every Vancouver installation where testing indicates it's needed. On high-moisture slabs, a dedicated vapour barrier coat goes in as a separate layer before the decorative system. This is the step most contractors skip.
Multi-Coat System
Minimum three coats on every residential installation: primer, high-build base coat, and UV-stable polyaspartic topcoat. No single-coat systems.
Written Quote First
Every project receives a written quote before any work begins. Confirmed at a free on-site assessment with no obligation to proceed.
Written Warranty
Every floor gets a written warranty, tiered by system. The 1-Day flake system carries 5 years on exterior floors and 10 years interior; the 2-Day system carries 10 years exterior and 20 years interior. Coverage includes adhesion failure, delamination, peeling, yellowing and hot-tire pickup.
Crack Filling on Every Job
Every crack is ground open and filled before any coating goes down, so it does not telegraph through the new floor. Wide or moving cracks are assessed first, and the repair is included in your written quote.
500+ Floors Completed
We take on garages, basements, shops, warehouses and commercial spaces across BC. Experience shows in the prep, because most coating failures start with a slab that was never ground, tested or repaired properly.
The Real Reason Epoxy Fails in BC
We get calls every week from homeowners whose epoxy floor is peeling within two years of installation. In almost every case, the cause is the same: moisture.
Greater Vancouver has one of the highest water tables in Canada. Combined with the coastal climate's above-average annual rainfall, a large proportion of Metro Vancouver slabs (especially those in Richmond, Delta, Burnaby, Coquitlam, and below-grade suites throughout the city) have moisture vapour emission rates above the threshold that standard epoxy requires.
A slab can seem dry on the surface and still be transmitting moisture vapour at rates that will cause a coating to delaminate within 12 to 24 months. The only way to know is to test. We test every slab. And we specify the system accordingly.
This is why our installations last 10 to 15 years and why floors installed without this step fail in 2 to 3. The coating itself is the same. The prep is what changes the outcome.
For more on BC floor coating standards, see the BC Building Code standards and WorkSafeBC construction guidelines.
Service Area: Greater Vancouver & BC
We install epoxy flooring throughout Metro Vancouver, the Fraser Valley, the North Shore, and Vancouver Island.
For projects outside these areas, call us at (604) 742-9479 to confirm coverage.
Ready to Talk About Your Floor?
Free on-site assessment. Written quote before any work begins. No obligation.
Get a Free On-Site Assessment
Tell us about the floor. We will look at the slab, test it for moisture, and send a written quote with the prep, the system and the warranty spelled out.